Search Results for ‘1050’

With the help of a good number of members , (Thank You!), I have been able to purchase all needed replacement parts for the LH hub on my 1050 transmission. Now that I am ready reassemble the transmission I am going by the exploded parts diagram and see that the 2 shims (PN's 1716498 & 1716499)...

I would like to sell these off as a package for $500. Trying to clean up before winter sets in. First up is a 68/69? 1050 PO took out the engine ( completely dismantled) that comes with it. A G series that has a donor Wisconsin TRA-10d engine and tires that hold air. Some other usable parts...

I had an amazing day with my son today. We drove to Camas Washington to get a Cub 123 and also ended up with a Bolen 1050 and a Simplicity(?) plow. The round trip was a little under 400 miles and the sky was blue and sunny for the first time in a while. We took lots of picture to show people...

Took my 1050 to a repair shop , they say in has no compression and that it might be a bent vale . And he go's on to say that parts are to hard to fine, and the engine is to old to used on a daily bases . My question is , are parts that hard to fine ? And can the Wisconsin engine be " wore out"...

The engine on my 1050 stop running and I have not had any time to work on it. I took it to a local lawn mower repair shop. First thing the guy says is "that parts for these tractors are hard to fine" I told him that Wisconsin has a local supply house in our area. And I know a guy in New York and...

Well my driveway parking area had some very bad ruts this spring from heavy rains and fast snow melts. My wife's car was close to rubbing is her tires were in the ruts my truck made. :wallbanging: So after doing much research on getting a back blade for my sleeve hitch, and deciding I would...

Has anyone ever put a 1050 transmission in a G-10 or know if its doable? I like the idea of the high/low range and the locking diff. So far ive never ran into anything my G-10 could get through or couldnt pull but I just like the idea of the locking diff and the high low range considering all...

I picked these up in up state NY this weekend. When I called the guy he said the larger of the two was a 1250 , it was not. Kind of glad they were both tube frames, more interchangeable. The 1050 I think is a parts tractor, engine is all there but disassembled. I think the rear is locked up too...

Ok, I have looked everywhere for the torque specs for the head bolts. I found the engine assembly manual, but I could not find anywhere that specified the torque spec. I was berated in my previous post about modern engine oil because I mentioned it leaked a little, so I have now ordered a new...

I have a Bolens 1050 that I bought a few years ago for $400 dollars with several attachments, weights, chains etc. Well, I had been using it year round and finally decided it was time to go through everything like I had when I first got it. Rear end play, lubrication, oil changes etc. My...

I am trying to fine the correct snow blade. have a Bolens 1050 and The manuals are not helping me . I don't went to go to michigan wisconsin pennsylvania . or ohio again for the wrong thing .What and were is the correct answer ???

I've got a Bolens 1050 and big plans to use it (but not abuse it). I don't know that I'll ever be able to justify spending what the hydraulic lift kits for these tractors is bringing and so I thought about using a 12V electric actuator. Anyone on here ever done that? I presume that the hydraulic...

Well, I can't say I added another Bolens because in the same trip, I sold a Bolens. I sold my 1455, mostly because I didn't have any attachments, and they seem to be harder to find and more expensive when you do find them. Being that I have all tube frames and a few decks, couple tillers, and...

Hi there, I'm looking for a carb or parts for this tractor. Its a 1969 Bolens husky 1050. I wanna say its a 6-9 HP Tecumseh engine. I cannot start looking until I find out what the carb is. I have the numbers on the carb if that helps they are 677 1E5. I'll be honest I lost the parts when I had...

I need a new transmission for my bolens husky 1050 1969. All the gears are ground up and there was about a half of of metal grindings on the plate. Not good! I also have a 2 broken teeth and a broken linkage so it need a lot. Anyone have a spare I'm in ct.

I am new to the old classic bolens tractors, however I now have a bolens 770 and just picked up a 1050. my 1050 has no mower deck but I have lines on a solid 19211. Can anyone tell me if this mower deck can work with my 1050?