Search Results for ‘1855’

I just picked up a Snapper 1855A with a snowplow, mower, and 3 point hitch. It's pretty rough, but does run. I'm pretty excited about it... I've wanted one of these for a long time. The engine doesn't smoke, although it's not the original... the seller also sold me another engine with it...

Hey there - Just wondering if anyone here has attempted installing a 35 HP Vanguard into a 1885? Any thoughts, ideas, concerns, issues, resources would be greatly appreciated. Thanks! Greg

Re-powered my Snapper / Massey 1855s. I am in Knoxville and have 3 Onans for sale. If you want all three, get in touch and we WILL make a deal. Won't ship, local pickup. P220 - runs fine, but smokes. Will probably need a rebuild in the future. $200 B48M. Runs but has a manifold leak. Tore...

Hello all, New member, but a bit of a long-time lurker I guess you could say. For years I've always had a liking for the Massey garden tractors and I finally took the plunge and bought a few items that were for sale locally. I fortunately, the fella that used to own them passed away and his...

I'm doing a temporary repower on my massey 1655 and have a predator 670 for it. I have other plans for the original clutch so I can't shim it to fit the 1" predator shaft. Does anyone know of a 1" pto clutch that will install on the predator? Eventually this tractor will get a kubota diesel...

Looking for plastic dash and console in very good condition for restoration project. NOS would be preferred but consider anything better than what I have. Located in Nova Scotia Canada so will need to be willing to ship. Thanks.

Up for sale here is a 1855 Snapper. Cousin to the Massey branded 1850s & 1650s. Not the best of shape but not the worst. Would be a good project or parts tractor. Good FEL platform. Guessing to be around an '83/84 vintage. The good Motor must have been swapped out at one point with an Onan P220...

My dad bought this tractor about five years ago, maybe more. I think he paid 850 for it and it came with a deck, the blower and some kind of lawn vac for the back. He scrapped the lawn vac and the deck which now I wished he hadn't done. He wanted it just for a snow mover for our cabin up north...

I was wondering what size implements I'll need for my 1855 and if any one knows a good place to get them.

I am restoring my late fathers M/F 1450 and am looking for the sand paper like material or oem decals to replace the originals that were on the foot tread areas. I am also looking for replacement decals for the dash board and plastic cover below the dashboard. Any help is appreciated. Kope

The front pto tube has no bearings left, the rear pto shaft has been cut with front haft missing. The deck has some broken welds so it hit an immovable object hard. no drive shaft for the deck. The blades look good so they must stay in "time"! The Onan is missing the exhaust flanges but has a...

i am looking for a pto shaft off of the front of a massey/snapper 1655 or 1855.its the one used to run the front and the mid pto.

i have a snapper 1855, according to the manual i read it says to use 10w30 or 10w40 motor oil in the transmission, is this right?

Hey everyone, I'm needing some help locating a couple parts that are NLA for an 1855 MF. The part numbers are: Snapper 49852 LINK, LOWER LIFT Snapper 7059574 PULLEY, TIMING BELT (RIGHT & LEFT SIDE) I appreciate any help! A friend bought a spindle shaft and spent a lot of money before knowing...

Well last week when we had the Snowpocolypse here in KC i did the good neighborly task of clearing 8 driveways for the elderly. No good deed goes by without a cost. As I came home I cleared the last 2 feet of our driveway only to have the chain on my snow blower twist and break. I spent...

It says it runs but quits. I'm guessing it's only a coil that went bad. Also it has a hydraulic leak on the loader. That should be an easy fix. If you know how much a loader costs, then you know this is a steal. http://delaware.craigslist.org/grd/3513447371.html

http://grandrapids.craigslist.org/grd/3420182868.html

I am slowly buying parts to restore the 1855 and Partstree.com is showing Snapper 1650 decals are available. They cost twice as much MF 1855 decals from MapleHunter. Any thoughts on keeping it badged as a Snapper? David