Garden Tractor Forums banner

Discussions Showcase Albums Media Media Comments Tags

1-17 of 17 Results
  1. Member Test Forum
    Testing, 1,2
  2. Parts
    Parting out a 1978 John Deere 312 tractor #81918 - Located in Cedar Rapids, IA 52404 and will ship for actual cost of shipping. $20 - Teardrop air cleaner assembly (very nice condition) $30 - H1 valve and levers $50 - frame $50 - fender pan (stripped) $10 OBO - dash pedestal (metal torn from...
  3. Parts
    I have a decent used hood support from a '77 312 that I am no longer using. There are 6 small holes in the front edge that can easily be welded shut. This piece is straight and would clean up very easily. Asking $25 and is available for pick-up in Cedar Rapids, IA 52404 but would consider...
  4. Parts
    I have a decent fender pan from a '77 John Deere 312 that I am no long going to use. With a bit of straightening and some crack repair you would have a decent pan for a worker or a bit of additional work for a show machine. I have stripped most of the paint with a wire wheel as you can see in...
  5. Parts
    I have a complete rear assembly out of a '78 John Deere 312. From what I can tell the tractor was parked when the input shaft twisted off. Someone tried to tap as well as re-drill the input shaft before the tractor was parked. It is complete with brakes and related hard lines. This one has...
  6. Parts
    I have a good used muffler off a John Deere 317 that had a Kohler KT-17 series II. I bought the engine as a spare for some of my other tractors and don't need the muffler. There is a dent in one side that I'm not sure if it was made that way or it got hit at some point in its life. You can...
  7. Parts
    I have a good used electric pto clutch off a John Deere 317 that had a Kohler KT-17 series II. I bought the engine as a spare for some of my other tractors and don't need the clutch. I hooked it up to a battery before I took it off and it made a nice strong snap as it activated. The bearing...
  8. Craigslist / Ebay / Kijiji Finds
  9. Craigslist / Ebay / Kijiji Finds
  10. John Deere Tractor Forum
    Hello all- I am new to this forum. I build mini dozers and this winter, I am converting a 1982 317 to a mini track dozer. I bought a 317 that had a fist sized hole in the crank case, for the hydrostatic trans and hydraulic outputs up front for the blade. I put a JB weld patch over the hole...
  11. 84 JD 317 with ONAN retrofit

    I got this tractor for nothing, and the only thing I have done to it is replace the voltage regulator.
  12. John Deere Tractor Forum
    For those interested Ive the JD 317 operator manual in pdf format. PM me if you want it.
  13. John Deere Tractor Forum
    Got home yesterday eve. The price tag was a bit higher than what I usually accept to pay but.... I just could'nt help it. In fact, I bought it for someone else who agreed to pay the price the seller was asking and to give me the rototiller in exchange for inspection and transport. All in all, I...
  14. John Deere Tractor Forum
    Last weekend I posted that one of my 317's that I was tilling with had a drive shaft failing. Yesterday after work, I puller the other 317 to the shop because the starter was out and I knew it had a good drive shaft in it to repair the other 317 and get back to tilling the garden. After I pulled...
  15. John Deere Tractor Forum
    So I mounted the Model 33 tiller on my 317 yesterday morning. i had noticed the last couple times I used the 317, I had a vibration that I could feel in the steering wheel and seat pan. i went to the garden and started tilling up the bed. By the time I got done, the vibration was very severe. I...
  16. John Deere Tractor Forum
    Is the lift link the same one for both the tiller and sleeve hitch?
1-17 of 17 Results