Garden Tractor Forums banner
1-13 of 13 Results
  1. Massey, Snapper, AMF Tractor Forum
    I reciently acquired, for free, a MF 10 garden tractor with the 410 mower deck. was going to make it my weed mowing tractor. The 4 spd trans internals were toast so I had to get them. but other than that and correcting some of the wiring, the tractor runs great. I was using it the other day...
  2. Kubota Tractor Forum
    No activity here since 2013 but I'm hoping. How do I get the pulley off the center shaft? Gears are out of gearbox and it has been removed. Tried 2 jaw puller and judicious heat, penetrating oil and cold. Pulley is bending but no movement on shaft. Anyone have a link to a manual? Several...
  3. Parts
    ISO. Massey Ferguson 1450 mower deck timing pulley. Just one of the outer pulleys not the bearing assembly.
  4. Idler clutch assembly

    Attachment kit for sears snow thrower
  5. Allis Chalmers, Simplicity Tractor Forum
    I picked up my tractor about 30 years ago and used it to clear snow off my long driveway and plow the sidewalk. I had a gravel driveway then and the lil' Model L with wheel weights and chains worked better than any snow blower I had tried. (didn't shear pins and throw the gravel everywhere!) I...
  6. Allis Chalmers, Simplicity Tractor Forum
    Simplicity Conquest, purchased new 2013, 50" mower deck. model 2691126. Smoke coming from the mower deck. Found that the hub (Part # 1713158SM) between the two pulleys (Part # 1713098SM) on the left side of the deck had two raised square guide blocks (is that what they are called?) which were...
  7. Bolens Tractor Forum
    Restoring a 1250 that had no starter/generator when I got it. I've rebuilt a S/G off a tube frame, but it cranks the engine too slowly. It has a pulley that's about 2 1/4" outside diameter. The parts catalogs show different part numbers for the pulleys between a 1050 and a 1250. For owners...
  8. Parts
    Hey. picked up a Bolens handi ho a few weeks back. Looking for a few ods and ends. 1702746 tank support 1700536 spring 1700468 sheave this is one with the hood. thanks to a good friend. finally will have the set of handi hos. got the engine apart and ready to reassemble. any help be...
  9. Massey, Snapper, AMF Tractor Forum
    Hey everyone, I'm needing some help locating a couple parts that are NLA for an 1855 MF. The part numbers are: Snapper 49852 LINK, LOWER LIFT Snapper 7059574 PULLEY, TIMING BELT (RIGHT & LEFT SIDE) I appreciate any help! A friend bought a spindle shaft and spent a lot of money before knowing...
  10. Parts
    Wanted a 2 speed engine pulley for a Simplicity walk behind the Model is L-1 belt drive.I have the large driven pulley,let me know what you have and how much money, would like to complete this little tractor after many years.Thanks Mike [email protected]
  11. John Deere Tractor Forum
    Hi everyone! This is my first riding mower, as my yards have never been large enough to justify upgrading from a push mower. My parents had decided to upgrade to a zero turn, so this John Deere LT133 made its way to my household. Its been taken care of relatively well, and hasn't given much...
  12. Garden Tractor Forum
    This is off my Massey 12, The cast broke when trying to remove it the stupid way (Hammer) ended up buying a real puller so no more of this happening, But how can I put these parts back on? I still have the parts and they fit perfect in the spots they came from< but how do I keep em there?
  13. Sears, Craftsman Tractor Forum
    Found one of these in a garage with a "bad" hydrostatic drive, didn't seem to interested in selling, tires look good & it started. couple days later he called me & said make offer, I said $100, he said not less than $150. 18 hp kohler, 48" cut. Is it worth it, are these repairable if there...
1-13 of 13 Results