Search Results for ‘transmission’

Hello all. My race mower currently has a Peerless 920 transmission. This transmission works great, except for one thing. I ordered some gears for the inside that were made for an 820. Here's where the hard part comes in. Since it would be too hard and expensive to make new gears compatible with...

Just creating a topic for the fluid type and parts diagrams. My unit is working but shifter is a little sloppy. Not sure if that's normal or if I'm missing a boot for up top or something. The shift lever has a removable top cap with 4 bolts attached to trans/dif unit and it looks as though I...

I'm new to the forum, but I've had my trusty G10 for a few years now, and have been working it hard. I used it to grade my yard and push rocks around, mow grass, and lots of plowing recently. During a storm last week the transmission suddenly stopped shifting into reverse. The reverse position...

What do you guys do for a transaxle flush? Keep in mind my bolens was sitting in a basement for 30 years untouched, and I'm sure there was no transaxle fluid change immediately beforehand. Normally i'd just warm it up, drain the old and in with the new but since it's been sitting so long and I...

So I just bought a running and driving B110. It appears to have broken lever which I believe is a Hi-Lo range selector. This is my first AC tractor. I’m new to antique tractors. It feels like it must be in low range based on the speed it goes but the small broken lever doesn’t feel like it’s...

With the help of a good number of members , (Thank You!), I have been able to purchase all needed replacement parts for the LH hub on my 1050 transmission. Now that I am ready reassemble the transmission I am going by the exploded parts diagram and see that the 2 shims (PN's 1716498 & 1716499)...

The left rear hub on my 1050 is scored so bad that I may need to replace it. (Any Sellers??) However I was wondering if it can be repaired somehow? Obviously if I just have it turned down to smooth the new OEM bronze bearing won't fit correctly. Thanks! Paul

Hello everyone. I bought a EK-10, got it running. When I try to shift into gear it grinds a little and doesn't move in any gear. High speed matched set belts are installed. Any help would be greatly appreciated.

Hello All, Looking for a K66L tuff tork transmission for a simplicity conquest. Trans can be bad, only need a good housing. Thank you, Mike

My mower is an MTD 13AK608G062 (2000) w/single speed transmission. When I put the tractor in forward gear and drive, I am hearing an very loud noise and am really trying to figure out what it is and where it's coming from. I'm not sure if it's a belt, pulley, brakes, wheels, low/dirty oil or...

Hey gang, Looking for some insight for my massey trans. 2 questions To make it relatively quick. Over the last 4 years or so I have had the one of two snap rings inside the differential that keeps the wheel axles into place come off its line and so as I turn I lose the right rear wheel as...

I am in the process of clearing out my grandfathers collection of power kings parts, tractors and implements. During the 70s-80s he was one of the largest PK dealers on the east coast. He has long since retired but we still have a large inventory including but not limited too: Snow blades...

Hi, I am new to the forum here. I have come to look for some help. I have a Ariens Max Zoom 2560 that has developed a pretty serious leak . In looking under the mower it appears to be on the right side (as you sit on it). Before tearing in to it I had hoped to connect to folks who may be...

I picked up a rough looking 234-01 that I want to restore mechanically for use as a working tractor. I've replaced the tires, overhauled the engine, I was able to buy bearings & seal for the differential area but need to go through the transmission as well. The tractor operates in all three...

Hi There, I fired up my Massey 1650 this spring, and noticed that when starting out in high there is a brief higher pitched whining noise (not grinding) when starting from a stop and accelerating in forward or reverse. Doesn't last long, maybe a quick second or two. As far as I remember it...

Hi Guys, So I went to fill up the transmission after flushing the old stuff out with diesel (thanks for the tip). I am a little confused about the info in the manuals. The owners manual says: - 1/2 pint 80/90 -1" below fill plug -The FILL plug is shown on the side of the machine, however...

I am a newbee to this site. I have owned a Craftsman 42" 21HP lawn tractor since 2010; Model 917.28922. In addition to cutting grass, I use it in the fall to mulch leaves so they deteriorate more quickly. The last two times out to mulch, the temperature has been low and the transmission has been...

I have owned a Craftsman 42" 21HP lawn tractor since 2010; Model 917.28922. In addition to cutting grass, I use it in the fall to mulch leaves so they deteriorate more quickly. The last two times out to mulch, the temperature has been low and the transmission has been very sluggish. I could not...

Hello to all, Been reading some of the posts, and well, Seems like a great place to ask questions. I'm a newbie, so please excuse my ignorance, and I'll apologize now if I'm in the wrong forum. So I'm looking for a tractor with a plow or snow-thrower, and there is little out there in the...

Looking for replacement spool caps for the hydraulic valve on a Massey / Snapper 1650. Either that or the entire valve itself if the price is right. Looking for both caps. Also looking for a used cooling fan for the transmission. I've been going over my recent purchase of a 1650, and noticed...